New 14 Motor Grader For Sale in Georgia

Engine

Base Power (1st Gear) - Net 238 hp

Engine Model Cat C13

Bore 5.1 in

Stroke 6.2 in

Speed at Rated Power 1,850 rpm

Note (3) Net power advertised is the power available at rated speed of 1,850 rpm, measured at the flywheel when engine is equipped with fan, air cleaner, muffler and alternator.

Standard Capability 122 °F

Note (2) Optimized VHP Plus is standard for the 14M3.

Torque Rise 41%

Maximum Altitude - Full Power 13900 ft

Maximum Torque - VHP Plus 1137 lb/ft

Emissions Tier 4 Final/Stage V, Tier 3/Stage IIIA equivalent or Tier 2/Stage II equivalent

Maximum Altitude - Full Power (Tier 3) 14349 ft

Maximum Altitude - Full Power (Tier 2) 12049 ft

Note (1) Net power is tested per ISO 9249, SAE J1349, and EEC 80/1269 Standards in effect at the time of manufacture.

Standard - Fan Speed - Minimum 550 rpm

Note (4) Power as declared per ISO 14396. Rated rpm 1,850. VHP+ = 228 kW (306 hp)

Displacement 763 in³

Number of Cylinders 6

Note (5) Cat engines equipped with a Selective Catalytic Reduction (SCR) system are required to use: Diesel Exhaust Fluid (DEF) which meets the requirements outlined in the International Organization for Standardization (ISO) standard 22241-1.

Standard - Fan Speed - Maximum 1,600 rpm

Weights

Operating Weight - Typically Equipped 57250 lb

Gross Vehicle Weight - Base* - Total 50980 lb

Gross Vehicle Weight - Base* - Front Axle 13994 lb

Gross Vehicle Weight - Typically Equipped - Total 57250 lb

Gross Vehicle Weight - Typically Equipped - Rear Axle 42005 lb

Gross Vehicle Weight - Typically Equipped - Front Axle 15245 lb

Gross Vehicle Weight - Base* - Rear Axle 36994 lb

Note *Base operating weight calculated on standard machine configuration with 20.5 R25 tires, full fuel tank operator and ROPS cab.

Moldboard

Blade Width 14 ft

Arc Radius 16.3 in

Throat Clearance 4.6 in

Blade Width - With End Bits 169 in

Blade Height - With Cutting Edge 24.9 in

Blade Width - Without End Bits 164 in

Blade Height - Without Cutting Edge 23 in

Frame

Circle - Outer Diameter 71.7 in

Front Axle - Wheel Lean - Left/Right 17.1°

Front Axle - Total Oscillation per Side 32°

Service Refill Capacities

Transmission and Differential 23.5 gal (US)

Diesel Exhaust Fluid Tank (Tier 4 Only) 5.8 gal (US)

Hydraulic System 33 gal (US)

Circle Drive 1.8 gal (US)

Cooling System 15.9 gal (US)

Fuel Tank 109.9 gal (US)

Blade Range

Maximum Depth of Cut 23.3 in

Circle Centershift - Left 25.6 in

Maximum Lift Above Ground 16.5 in

Circle Centershift - Right 20.5 in

Blade Tip Range - Backward 5°

Maximum Shoulder Reach Outside of Tires - Right 78.9 in

Moldboard Sideshift - Right 31.1 in

Moldboard Sideshift - Left 29.1 in

Maximum Shoulder Reach Outside of Tires - Left 73.6 in

Blade Tip Range - Forward 40°

Air Conditioning System

Air Conditioning The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 2.0 kg (4.4 lb) of refrigerant which has a CO2 equivalent of 2.860 metric tonne (2.76 ton).

TECHNOLOGY THAT GETS WORK DONE

Optional Stable Blade improves grading precision by decreasing engine speed at 15 percent intervals when machine bounce is detected then increases engine rpm systematically when grader stabilizes.
Optional Cat Grade with Cross Slope helps maintain desired cross slope by automatically controlling one side of the blade.
Optional Cat Grade uses positioning and guidance technologies, machine sensors, and automatic blade control to help get to grade faster, easier, and more efficiently.
Optional Auto Articulation allows you to articulate automatically while steering in tight spaces or around curves, obstacles, and turnarounds.
Manage your fleet of machines while reducing fuel burn with Cat Production Measurement System option. The Efficiency Coach and Application Segmentation work together to monitor operators and machines at the same time. Measure your jobsite’s efficiency and productivity from anywhere on the website.

MOVE MORE, BURN LESS

Cat C13 engine meets U.S. EPA Tier 4 Final/EU Stage V, Tier 3/Stage IIIA equivalent or Tier 2/Stage II equivalent emission standards, depending on emission standards of specific country.
Standard Economy Mode can be turned on to limit maximum engine speed which helps reduce fuel consumption.
Standard VHP Plus provides ideal amount of power in all gears.
Standard Automatic Differential Lock unlocks differential during a turn and re-locks when straight for easier operation and improved power train protection.

MORE CONTROL AND EFFICIENCY

Load-sensing system and advanced electro hydraulics give operator superior implement control and hydraulic performance.
Proportional Priority Pressure-Compensating valves have different flow rates for head and rod ends of cylinder so machine responds consistently and predictably.
Balanced hydraulic flow is proportioned to ensure all implements will operate at the same time without slowing engine or speed of some implements.

DESIGNED FOR OPERATORS

Simple, intuitive joystick controls replace levers, so hand and arm movement is reduced by 78%, helping reduce operator fatigue.
Optional Advanced Control Joysticks allow operator to control automated grading solutions efficiently and safely without removing hands from the joysticks.
Selectable blade lift modes – Fine, Normal, or Coarse – allow operator to match application requirements.
Articulation Return-to-Center automatically returns machine to a straight frame position from any angle with the touch of a button.

BUILT-IN SAFETY FEATURES

Optional rear vision camera enhances sight to rear of machine.
Electrical disconnect and engine shutoff switches are ground level.
Operator Presence System keeps parking brake engaged and hydraulic implements disabled until operator is seated and machine is ready for operation.
Hydraulic Lockout disables all implement functions while still providing machine steering control – especially useful while roading.
Optional seat belt indicator promotes safe operating habits.

SAVE MAINTENANCE TIME

Convenient access from the top of the circle to the patented top-adjust wear strips and inserts make them easy to add or replace.
Shim less Moldboard Retention System uses vertical and horizontal adjusting screws to keep moldboard wear strips aligned for reduced blade chatter and precise blade control.