New Cat 907 Compact Wheel Loader For Sale in Georgia

Engine

Maximum Gross Power 74.7 hp

Engine Model Cat C2.8*

Maximum Engine Speed 2550 rpm

Maximum Gross Power - Rated Engine Speed 2400 r/min

Maximum Gross Power - SAE J1995 74.7 hp

Maximum Gross Power - ISO 14396 74.3 hp

Maximum Gross Power - ISO 14396 (metric) 75.3 mhp

Rated Net Power - Rated Engine Speed 2400 r/min

Rated Net Power - SAE J1349 72.7 hp

Rated Net Power - ISO 9249 72.1 hp

Rated Net Power - 2,400 rpm - ISO 9249 (metric) 73.1 mhp

Maximum Gross Torque - SAE J1995 222 lb/ft

Maximum Gross Torque - ISO 14396 221 lb/ft

Maximum Net Torque - SAE J1349 218 lb/ft

Maximum Net Torque - ISO 9249 217 lb/ft

Displacement 171 in³

Bore 3.54 in

Stroke 4.33 in

Note *Meets U.S. EPA Tier 4 Final and EU Stage V emission standards.

Note (1) Advertised power is tested per the specified standard in effect at the time of manufacture.

Note (2) Net power advertised is the power available at the flywheel.

Note (3) #Maximum gross and net torque measured at 1,600 rpm.

Weights

Operating Weight 12765 lb

Buckets

Bucket Capacities 0.75-1.55 m³ (1.0-2.0 yd³)

Bucket Capacities - General Purpose 0.80-1.35 m³ (1.0-1.7 yd³)

Bucket Capacities - Light Material 1.25-1.55 m³ (1.6-2.0 yd³)

Multi-Purpose 0.75-1.1 m³ (1.0-1.4 yd³)

Note Bucket selection must be made with an understanding of the material density and application to ensure machine stability is maintained within the tipping loads stated per model and configuration.

Note (1) Bucket capacities stated include BOCE, in line with ISO 7546.

Service Refill Capacities

Fuel Tank 24 Gal

Cooling System 3.2 Gal

Engine Crankcase 2.3 Gal

Axles - Front Center Differential 2.3 Gal

Axles - Rear Center Differential 2.3 Gal

Hydraulic System - Including Tank 17.8 Gal

Hydraulic Tank 11.8 Gal

Transmission 0.6 Gal

Note No Diesel Exhaust Fluid (DEF) fluid needed on this size engine.

Axles

Front Fixed (standard), Locking Differential (optional)

Rear Fixed (standard), Locking Differential (optional)

Note Oscillation of ±11 degrees via hitch between front and rear frames.

Steering

Steering Articulation Angle - Each Direction 39 °

Maximum Flow - Steering Pump 12.3 gal/min

Maximum Working Pressure - Steering Pump 3336 psi

Steering Cycle Times – (full left to full right) – at High Idle 2.8 s

Number of Steering Wheel Turns - Full Left to Full Right or Full Right to Full Left 3.25 turns or 4.00 turns

Transmission

Forward and Reverse - Speed Range Creep# 6 mile/h

Forward and Reverse - Speed Range 1* 6 mile/h

Forward and Reverse - Speed Range 2** - High Speed 10.5 mile/h

Forward and Reverse - Speed Range 2** - Standard 12 mile/h

Forward and Reverse - Speed Range 3*** 25 mile/h

Note #Factory default shown, can be adjusted to any speed up to 19 km/h (12 mph).

Note (1) *Creep function not available in this gear or above.

Note (2) **Max speed dependent on model and configuration (standard vs. high speed transmission).

Note (3) ***Reverse is 30 km/h (19 mph).

Tires

Tire Size - Standard *405/70 R18 SPT9

Tire Size - Optional 405/70 R18 Powerloads

Tire Size - Optional (1) 340/80 R18 XMCL/Bibload

Tire Size - Optional (2) 340/80 R18 TRI 2

Tire Size - Optional (3) 40X14-20 TL, SM/TR

Tire Size - Optional 4 340/80 R18 Duraforce

Note *This tire has been used for all dimension, stability and performance data.

Note (1) Other tire choices are available. Contact your Cat dealer for details.

Note (2) Caterpillar recommends that you consult a tire supplier to evaluate all conditions before selecting a tire model.

Cab

ROPS ISO 3471:2008

FOPS ISO 3449:2005 Level II

Note (1) Canopy and cab, Rollover Protective Structures (ROPS) are available worldwide. Canopy not available in EU.

Note (2) The declared dynamic operator sound pressure levels per ISO 6396:2008*, when properly installed and maintained, is 71 dB(A).

Note (3) *Measurements were conducted with the cab doors and windows closed.

Note (4) The labelled sound power level for the CE marked configurations when measured according to the test procedure and conditions specified in 2000/14/EC is 101 dB(A). 99 dB(A) Low Sound – Option available.

Loader Hydraulic System

Main Relief - 1st Auxiliary (3rd slice) 3408 psi

Main Relief - 1st Auxiliary (3rd slice) - Standard Flow* 21 gal/min

Main Relief - 1st Auxiliary (3rd slice) - High Flow* 32 gal/min

Main Relief - 2nd Auxiliary (4th slice) 3408 psi

Main Relief - 2nd Auxiliary (4th slice) - Flow 12 gal/min

Hydraulic Cycle Time - Rackback 2.2 s

Hydraulic Cycle Time - Lift 5 s

Hydraulic Cycle Time - Dump 1.6 s

Hydraulic Cycle Time - Float Down 2.8 s

Note * Maximum flow stated, actual flow delta could be 6% from data shown. Also adjustable from 20% to 100% of maximum flow through display.

Dimensions - With HPL-V Coupler - Approximate#

Height: Ground to Cab** 8.5 ft

Height: Ground to Beacon** 9.08 ft

Height: Ground Axle Center** 1.58 ft

Height: Ground Clearance** 1 ft

Length: Overall* 17.58 ft

Length: Rear Axle to Bumper 4.58 ft

Length: Hitch to Front Axle 3.58 ft

Length: Wheel Base 7.08 ft

Length: Front Axle to Front of Coupler 3.5 ft

Clearance: Bucket at 45° * 8.25 ft

Clearance: Load over Height** 9.5 ft

Clearance: Level Bucket** 9.92 ft

Height: Bucket Pin** 10.67 ft

Height: Overall** 13.5 ft

Reach: Bucket at 45° * 2.33 ft

Carry Height: Bucket Pin 1.08 ft

Dig Depth** 0.33 in

Width: Bucket 6.75 ft

Width: Tread Center 4.67 ft

Turning Radius: Over Bucket 14.75 ft

Width: Over Tires 6.07 ft

Turning Radius: Outside of Tires 12.92 ft

Turning Radius: Inside of Tires 6.75 ft

Rack Angle at Full Lift 56°

Dump Angle at Full Lift 45°

Rack Angle at Carry 51°

Departure Angle - Degrees 30°

Articulation Angle - Degrees 39°

Operating Weight: Bucket ^ 12689 lb

Tipping Load - Straight - ISO 14397-1 † 9773 lb

Tipping Load - Full Turn - ISO 14397-1 † 8235 lb

Operating Weight: Carriage and Tines ^^ 12220 lb

Tipping Load - Straight † 7807 lb

Tipping Load - Full Turn † 6569 lb

80% of Tip: Firm and Level EN474-3 †† 5255 lb

Note (1) *Vary with bucket

Note (2) **Vary with tire

Note (3) ^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL),1.05 m3 (1.4 yd3) general purpose bucket.

Note (4) ^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class II carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center).

Note (5) †Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing.

Note (6) ††Full compliance to EN474-3 and SAE J1197.

Note (7) #HPL-A weight, tipping and rated loads are within 1% of the HPL-V.

Note (8) Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9 405/70 R18 tires and 1.05 m3 (1.4 yd3) general purpose bucket with bolt-on cutting edge or a class II fork carriage and tines, (tire supplier variability can impact dimensions by 2%).

Note (9) Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9.

Dimensions - With SSL Coupler - Approximate

Height - Ground to Cab 8.5 ft

Height: Ground to Beacon** 9.08 ft

Height: Ground Axle Center** 1.58 ft

Height - Ground Clearance 1 ft

Length - Overall with Bucket 18.17 ft

Length: Rear Axle to Bumper 4.58 ft

Length: Hitch to Front Axle 3.58 ft

Length - Wheel Base 7.08 ft

Length: Front Axle to Front of Coupler 4.33 ft

Clearance - Bucket at 45° 7.83 ft

Clearance: Load over Height** 9.5 ft

Clearance - Level Bucket 9.92 ft

Height - Bucket Pin 10.67 ft

Height: Overall** 13.83 ft

Reach - Bucket at 45° 2.67 ft

Carry Height: Bucket Pin 1.17 ft

Dig Depth 3 in

Width - Bucket 6.75 ft

Width - Tread Center 4.67 ft

Turning Radius - Over Bucket 15 ft

Width - Over Tires 6.08 ft

Turning Radius: Outside of Tires 12.92 ft

Turning Radius - Inside Tire 6.75 ft

Rack Angle at Full Lift 51°

Dump Angle at Full Lift 50°

Rack Angle at Carry 46°

Departure Angle - Degrees 30°

Articulation Angle - Degrees 39°

Operating Weight: Bucket ^ 12897 lb

Tipping Load – Straight – ISO 14397-1 † 8653 lb

Tipping Load – Full Turn – ISO 14397-1 † 7257 lb

Operating Weight: Carriage and Tines ^^ 12414 lb

Tipping Load - Straight † 7416 lb

Tipping Load - Full Turn † 6266 lb

80% of Tip: Firm and Level EN474-3 †† 5013 lb

Note (1) *Vary with bucket

Note (2) **Vary with tire

Note (3) ^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL),1.05 m3 (1.4 yd3) general purpose bucket.

Note (4) ^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class II carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center).

Note (5) †Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing.

Note (6) ††Full compliance to EN474-3 and SAE J1197.

Note (7) #HPL-A weight, tipping and rated loads are within 1% of the HPL-V.

Note (9) Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9.

Sustainability

Recyclability 93%

CONFIGURED FOR SUCCESS

Cat® wheel loaders set the standard for productivity, fuel efficiency and operator comfort. The Cat 907 Compact Wheel Loader has a high torque C2.8 engine that works in conjunction with an intelligent hystat power train to deliver exceptional fuel efficiency. This engine meets U.S. EPA Tier 4 Final and EU Stage V emission standards with a clean emission module designed to manage itself so you can concentrate on the task at hand.

ENJOY ALL DAY COMFORT

All new cab is spacious, quiet and comfortable with all around 360° visibility to keep you productive throughout the day. Seat-mounted controls feature a multifunction joystick for lift and tilt functions with an integrated thumb operated speed range, forward/neutral/reverse (FNR) switch, trigger operated differential lock and constant flow. Optional fourth function joystick also available.
Digital display with soft touch buttons for customized settings to easily control linkage and drive train to further enhance operator comfort and safety.

EFFICIENTLY POWERFUL

Cat C2.8 engine provides a cleaner, quieter operation while delivering superior performance and durability through a high torque, low speed design. Caterpillar’s exclusive Intelligent Power Management system monitors operator input and available power to keep the machine working at peak efficiency.
“Shift on the go” locking differentials and hydrostatic transmission provide smooth and powerful operation while increasing the efficiency of machine cycles. New Powertrain (Utility) Mode via the display enables right pedal machine operation giving further improved operator controllability of attachment RPM versus machine ground speed over creep control and inching pedal.

WORK MADE EASY

All-in-one joystick to keep eyes on the work while maximizing operation of hydro-mechanical attachments with a state of the art pressure compensated electro-hydraulic system. Optimized Z-bar linkage for great performance and versatility with buckets that now have the DNA of the larger Cat loaders, such as curved side plates and a flat torque tube for parallel reference to the cutting edge.

CUSTOMIZE YOUR EXPERIENCE

Work as one with your machine by customizing the controls. Operator can adjust machine responsiveness with the push of a button based on the attachment or application. Once customized, settings can be locked with “simplified mode” to ensure the machine is consistent and intuitive for every user.
Machine security is enhanced with a standard keycode or optional Bluetooth® technology.

PURPOSE BUILT SPECIALTY MODELS

Machines can be built to meet industry and application specific needs: Agriculture, General Construction, Industrial and Waste, Landscaping or Snow Removal.
The 907 is availble with the following specific handler arrangements: Ag Handler and Waste Handler

AFTERMARKET AND SERVICES

Range of services and aftermarket retrofits and upgrades available to keep your machine going and configured for your application.
Service and maintenance parts available, including a range of self-service options (SSO) and dealer installed kits.
Integrated Technology available to reduce service costs and maintenance.

SUSTAINABILITY

The Cat® C2.8 engine meets U.S. EPA Tier 4 Final and EU Stage V emission standards.
Engine Idle Shutdown Timer reduces fuel burn, greenhouse gas emissions and unnecessary idle time by shutting down the machine after a pre-set idling period.
Remote Troubleshoot decreases maintenance time and keeps your machine running with maximum efficiency by allowing your Cat dealer to virtually test the machine while working. Once a problem is identified, a technician can fix it the first time, saving time and money.
Remote Flash minimizes downtime and maintenance time while keeping your asset running with maximum efficiency. Alerts for machine updates are sent virtually from your Cat dealer and updates can be deployed without a dealer technician needing to be onsite.
Advanced Electro Hydraulic System provides the optimum balance of power and efficiency while giving you the control you need for your precise jobsite requirements.
Engine Demand Fan is hydraulically driven to provide machine cooling only when needed, improving fuel efficiency and reducing greenhouse gas emissions.
Hydrostatic Transmission is an efficient way to transfer engine power to the wheels at low speeds versus a torque converter.
Efficient HVAC regulates temperature control. No need to leave the machine running to cool the cab.
Shift on the go transmission, means no need to stop so you keep your momentum.